Select switch ports that will receive the Equallogic and:
PVID = 2 (DCB VLAN)
Type = Trunk
VLAN = 2 Untagged

DO NOT FORGET to save switch configuration …

—-
grpadmin
grpadmin
489:5:netmgtd:15-Feb-2017 07:08:26.040005:rcc_util.c:1024:INFO::25.2.9:CLI: Logi n to account grpadmin succeeded, using local authentication. User privilege is g roup-admin.
It appears that the storage array has not been configured.
Would you like to configure the array now ? (y/n) [n]y
Group Manager Setup Utility
The setup utility establishes the initial network and storage
configuration for a storage array and then configures the array
as a member of a new or existing group of arrays.

For help, enter a question mark (?) at a prompt.

Do you want to proceed (yes | no ) [no]: yes
493:259:SP:15-Feb-2017 07:09:51.210259:verify.c:1066:INFO::14.2.12:0:Parity verification initiated on RAID LUN 0.
494:260:SP:15-Feb-2017 07:09:51.210260:verify.c:1066:INFO::14.2.12:0:Parity verification initiated on RAID LUN 0.
495:261:SP:15-Feb-2017 07:09:51.210261:verify.c:1066:INFO::14.2.12:0:Parity verification initiated on RAID LUN 0.

Initializing. This may take several minutes to complete.

.

Enter the network configuration for the array.

Member name []: newstorage
Network interface [eth0]:

Data Center Bridging (DCB) is active on the specified interface. The
VLAN ID for this interface is needed in order for DCB to operate
correctly.

DCB VLAN Identifier []: 2
IP address for network interface []: 192.168.130.99
Netmask [255.255.255.0]:
Default gateway [192.168.130.1]:

Initializing interface eth0. This may take a minute…..

Enter the IP address and name of the group that the array will join.

Group name []: newstorage-group
Group IP address []: 192.168.130.98

Searching to see if the group exists. This may take a few minutes.

The group does not exist or currently cannot be reached. Make sure
you have entered the correct group IP address and group name.

Do you want to create a new group (yes | no) [yes]:

Group Configuration

Group Name: newstorage-group
Group IP address: 192.168.130.98
Do you want to use the group settings shown above (yes | no) [yes]:
Password for managing group membership: <password>
Retype password for verification: <password>

Password for the default group administration(grpadmin) account: ht
Retype password for verification: <password>

Saving the configuration…

Waiting for configuration to become active….Done
1174:40:psgd:15-Feb-2017 07:19:06.720040:psgd_group.cc:18045:INFO::18.2.0:Group member newstorage now active in the group.

Group newstorage-group has been created with one member.
Use the Group Manager GUI or CLI to set the RAID policy
for the member. You can then create a volume which
a host can connect to using an iSCSI initiator.
To access the Group Manager GUI, specify http://192.168.130.98 in
a Web browser window. To access the CLI, use telnet or SSH to
connect to the group IP address from a remote terminal, or attach a
console terminal directly to a serial port on a group member’s
active control module. Log in to the default group administration
account (grpadmin) using the password you specified when creating
this group. See the Group Administration manual for more
information.
newstorage-group> member show
Name Status Version Disks Capacity FreeSpace Connections
———- ——- ———- —– ———- ———- ———–
newstorageonline V9.0.2 (R4 26895) 24 0MB 0MB 0
member select newstorage

newstorage-group(member_newstorage)> eth show
Name ifType ifSpeed Mtu Ipaddress Status Errors DCB
—- ————— ———- —- —————————– —— —— ——
eth0 ethernet-csmacd 10 Gbps 9000 192.168.130.99 up 0 on
eth1 ethernet-csmacd 10 Mbps 1500 down 0 off
eth2 ethernet-csmacd 10 Mbps 1500 down 0 off
> eth select 2
emprestado-group(member_emprestado eth_2)> ipaddress 10.11.0.27 netmask 255.255.0.0
Changing the IP address closes all management and iSCSI connections associated w
ith this IP address. Do you really want to change? (y/n) [n]y
> mgmt-only enable
> up
This port is for group management only. Make sure it is connected to a dedicated
management network.
Do you want to enable the management interface? (y/n) [n]y

> save-config

Go to web interface,:
Create RAID 6 (Pool Member)
Create Volume and define access groups for iSCSI (IQN based only, no username, no IP)

Advertisements